Search Results

Since 1968, vehicle weight increases and emissions controls have reduced fuel economy substantially. Additional losses in economy and acceleration will be experienced through 1976. Recommendations are made to lessen the impact of the predicted losses. Factors influencing fuel economy and acceleration are examined for an intermediate car. Changes in engine efficiency and displacement, compression ratio, torque converter, transmission, axle ratio, aerodynamic drag, tires, accessories, vehicle weight, and emissions controls are examined. When practical, the effects of 10% changes are analyzed. Comparisons are also made with a subcompact and a luxury vehicle.

There is a major problem in maintaining the records of the more than 275 million vehicles presently registered throughout the world. Monitoring the life of a given vehicle from its fabrication to its destruction can best be accomplished by the inner facing of major computer programs and a uniform system for vehicle identification. The Vehicle Identification Number (VIN) is the legal identification of the vehicle. Every manufacturer has the responsibility of assigning a unique VIN to each vehicle, in compliance with numerous procedures, standards and laws. The VIN is attached to the vehicle, stamped and embossed on components, and printed on tamper resistant labels. It is printed on hundreds of documents and maintained in numerous files.

THE design and construction of the PowerFlite automatic transmission are described by the authors. It is of the torque converter type, some models being water-cooled, while others are direct air cooled. Details of the hydraulic controls are explained, including the one-piece shift valve and the shuttle valve for controlling closed-throttle shifts. It is claimed that this transmission has relative simplicity, light weight, and smoothness of operation.

THE GRADEABILITY formula can be used as the basic means for rating a truck transmission. By correlating the gradeabilities in the various gear ratios with a highway requirement probability curve, the per cent of time in each ratio can be obtained. The required hours of gear life for each ratio are then determined, and compared with the available gear life in the ratios. This procedure gives a detailed analysis of a transmission rating for one vehicle specification at a specified mileage between overhauls. A limitation of the system is that it cannot be applied quickly to various vehicle specifications. The paper outlines the method for constructing a nomogram to overcome this.*

THIS PAPER describes balanced-life concept of gear design — in which the gear and pinion are designed to fail simultaneously. An example is presented to show how this concept allows a combination of minimum size and maximum capacity in gas turbine application. Various reasons for failure and factors in long gear life are discussed. The author analyzes the calculations needed and their programming for a digital computer. Calculating gear designs for production is a time consuming, demanding task to do manually. The use of the computer has changed this — and brought about better gear design by making it possible to study more detailed analyses to evolve optimum solutions. This paper was the Sixth L. Ray Buckendale Lecture, presented at the 1960 SAE Annual Meeting.

A laboratory test fixture was designed and built to simulate seat belt assembly installations. The anchor positions of the retractor and pillar loop, and the engaged or free-hanging position of the latchplate can be varied to either simulate a vehicle's seat belt system geometry, or to optimize a proposed geometry. The required retraction forces for a simulated geometry are determined by replacing the retractor action with a motorized load transducer that measures the force required to stow the latchplate. The pillar loop, webbing, latchplate, and their relative positions can be varied until the minimum retraction force that successfully stores the latchplate is determined. The geometry of such a condition can then be applied to future designs of seat belt assembly components and their anchor positions.

A method has been employed in the stamping facility to reduce scrap by correlating observations from the press shop with laboratory test results. This paper illustrates the successful use of this method for reducing formability failures. Correlation of observed coating behavior with laboratory adherence tests is also discussed.

Testing of an OHC valve train with hydraulic lash adjuster in which the valve displacements, velocities and accelerations were measured and analyzed in both time and frequency domains, coupled with analysis of the frequency content of the valve acceleration function and its ramps, show that traditional designs of the opening and closing ramps used on some IC engine valve cams can exacerbate vibration in the follower system causing higher levels of spring surge and noise. Suggestions are made for improvement to the design of the beginning and ending transitions of valve motion which can potentially reduce dynamic oscillation and vibration in the follower train.

Gasoline direct injection technology is receiving increased attention among automotive engineers due to its high potential to reach future emission and fuel economy goals. This paper reports some of the design and development techniques in use at Chrysler as applied to four-stroke Direct Injection Spark Ignition (DISI) engines. The spray characteristics of Chrysler's single-fluid high-pressure injector are reported. Tools used in the design process are identified. Observations of the in-cylinder fuel/air mixing process using laser diagnostic techniques and Computational Fluid Dynamics (CFD) are described. Finally, combustion and emissions characteristics using Design of Experiment (DoE) tests are presented.

An automotive cockpit module is a complex assembly, which consists of components and sub-systems. The critical systems in the cockpit module are the instrument panel (IP), the floor console, and door trim assemblies, which consist of many plastic trims. Stiffness is one of the most important parameters for the plastic trims' design, and it should be optimum to meet all the three functional requirements of safety, vibration and durability. This paper presents how the CAE application and various other techniques are used efficiently to predict the stiffness, and the strength of automotive cockpit systems, which will reduce the product development cycle time and cost. The implicit solver is used for the most of the stiffness analysis, and the explicit techniques are used in highly non-linear situations. This paper also shows the correlations of the CAE results and the physical test results, which will give more confidence in product design and reduce the cost of prototype testing.

THE design and development of the new valve-in-head V-8 Chrysler engine of 7.5 compression ratio are described here. Among the features discussed by the authors are: the hemispherical combustion chamber, V-8 cylinder arrangement, double-breaker distributor, “thermal flywheel” on automatic choke, and exhaust-heated and water-jacketed throttle bodies. The hemispherical combustion chamber was adopted after it had displayed excellent volumetric and indicated thermal efficiencies, and an ability to maintain these high efficiencies in service. The high volumetric efficiency, for example, is considered to be due to such design features as valves not crowded together, nor surrounded closely by the combustion-chamber walls. They are thereby fully effective in the flow of the fuel-air mixture and the exhaust gases. The authors also present performance data for this engine, which, at full throttle, develops 180 hp at 4000 rpm and 312 ft-lb of torque at 2000 rpm.

INDUCTION heating is a process or method by which metal parts are heated by simply placing them in an alternating magnetic field. The action is that of the transformer, whereby electrical energy is transferred or passed over to another isolated electric or secondary circuit by means of the magnetic field; thus, no physical attachments or electrical contacts are necessary to have electrical currents, which are dissipated as heat, flow in the parts to be processed. The strength and frequency of the alternating magnetic field can be selected to produce any desired rate of heating and ultimate temperature. A circuit can be set up to dry lacquer at 160 deg. fahr. on thin sheet-metal parts or to melt in record time immense steel ingots. Induction heating is now commercially applied in automotive production to many processes, and these are specified.